Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
The content below pertaining to Installing A Bathtub is absolutely remarkable. You should check it out.
Installing a tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably tough project. If the old tub is conveniently obtainable, the task can relocate easily; if you need to open up a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to leave the old tub and embeded in the new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to alter the plan of your previous water system pipes.
Your tools as well as material checklist should comprise the following:
Preparing for the Installation
Firstly, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its last setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up faucets, fit all-time low of the furthest versatile tap port to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and check all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the tub and additionally examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait until the bath tub has actually been utilized at least when as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, bring about problems with moisture and also possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can split rather early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the tiles using waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that blog entry about How to Install a Bathtub Yourself when doing a search on the internet. Sharing is nice. One never knows, you will be doing someone a favor. Many thanks for your time. Come back soon.
Get Started Report this page